General Chemistry Lab Techniques Cheatsheet

Author image
Reviewed by
Dr. Mike Christiansen
Key Takeaway
Table of Contents

    Basic Techniques

    Calorimetry

    Calorimetry is used to measure the change in heat (released or absorbed) during a chemical reaction. In chemistry labs, the setup for calorimetry generally consists of a Styrofoam cup with a sealed lid and hole for thermometer to measure the change in temperature during the reaction.

    Centrifugation

    Centrifugation is used to separate solids and liquids in heterogeneous mixtures. Successful separation results in the solid portion (pellet) at the bottom of the centrifuge tube and the liquid portion (supernatant) above it. When using a centrifuge, it is important that it remains balanced at all times – any tube being spun should have one of equal volume placed in the opposite slot.

    Quantitative transfer

    Proper quantitative transfer methods ensure that the entire quantity of a substance has been transferred (for example, if an experiment requires that 5g of a powder are transferred into a beaker, it is easy for small amounts of the powder to be lost during transfer or left behind on the transfer medium – this can affect accuracy of results).

    When transferring powders, the mass should first be measured on creased weighing paper. Next, the weighing paper should carefully be folded and tipped into its destination (e.g. a beaker). A spatula should then be tapped against the paper to dislodge any remaining powder. Finally, the paper should be rinsed into the beaker to ensure full transfer of the powder.

    When transferring a liquid, after it is poured into its destination,  the sides of the vessel it was poured from should be rinsed with solvent and continue to be poured into the destination to ensure that all of the liquid has been transferred.

    Titration

    Titration allows one to determine the endpoint of a reaction and the quantity of reactant used to achieve it. Titration generally involves a buret (to deliver precise amounts of the titrant) and a flask (generally an Erlenmeyer flask) containing the solution.  An indicator that changes color is used to determine when the equivalency point has been crossed once sufficient quantity of the titrant has been added. Sometimes, a pH meter will be used to detect the endpoint rather than an indicator.  

    Filtration

    Filtration is used to separate solids from liquids in a mixture. In some cases, pouring the solution through filter paper set in a Buchner funnel over a flask. To filter more effectively, a filter flask is used in combination with a vacuum outlet to effectively suck the liquid solution through the filter paper (vacuum filtration). After successful filtration, the solid is left behind on top of the filter paper while the liquid collects in the flask below.  

    Distillation

    Separates miscible liquids (mix together well) according to differences in boiling points. Often uses a piece of equipment known as a condenser.

    Decantation

    Separates liquids from solids by pouring the liquid carefully off the top of a container.

    Extraction

    Separates two liquids that don't mix very well due to a difference in polarity, i.e. separating water-soluble (polar) liquids from nonpolar ones. This procedure uses an instrument known as a separatory funnel.

    Reading the meniscus:

    When measuring volume in graduated glassware, one should always read a meniscus from the bottom of the curve. In the image below, one’s eye should be level with the dotted line:

    Drying glassware

    Some glassware can be placed in an oven for drying, but volumetric glassware (e.g. pipets, burets, volumetric flasks, graduated cylinders, etc.) should never be placed in an oven -  the heat can ruin the calibration.

    Cleaning glassware

    Once glassware is cleaned with soap or detergent in tap water, it should then be rinsed with deionized water to avoid potentially contaminating future solutions with small concentrations of residual ions.

    Lab Equipment Explained

    Beaker

    Beakers can be used for the transfer of liquids, mixture of liquids, or for reactions – however, beakers are not accurate and should not be used for measurements.

    Graduated cylinder

    A graduated cylinder can be used for the transfer of liquids or for general measurements (with accuracy varying based on the extent of volume indications present – e.g., to the nearest mL). They are not the most accurate method of transferring liquids – a pipette or buret is better suited for transfer of liquids when very high accuracy is needed.  A graduated cylinder (along with any other form of volumetric container holding a liquid) should always be read from the bottom of the meniscus (see Data Analysis for additional details).

    Erlenmeyer flask

    Like a beaker, an Erlenmeyer flask can be used for the transfer of liquids, mixture of liquids, or for reactions – but is not accurate and should not be used for measurements. Since an Erlenmeyer flask has a narrower neck than a beaker, it helps prevent splashing outside of the container (this is particularly useful during titrations, where a liquid is being dropped into a solution).

    Volumetric flask

    A volumetric flask is used as a container for a liquid of a known, precise amount (or the creation of a mixture to a known volume). These flasks have a very narrow neck along which there is a mark for the precise amount the flask holds (e.g. one can be confident a 250 mL volumetric flask with liquid up to the marking point contains almost exactly 250 mL).

    Filter flask

    A filter flask is used during vacuum filtration. It is very similar in appearance to an Erlenmeyer flask, but the side of the neck contains a protruding “side arm” along which a vacuum hose can be fixed to create suction.

    Test tube

    Like beakers, test tubes can be used for the transfer of liquids, mixture of liquids, or for reactions – but they are not accurate for measurements of volume and should not be used for this purpose. They are generally useful for the transfer of smaller quantities of liquid.

    Pipet

    A pipet is used for the measurement and transfer of very precise amounts of liquid. Pipettes may be graduated (with several markings for varying volume) or volumetric (a single marking for a set volume). Volumetric pipets are recognized as the best tool for the measurement and transfer of very precise amounts of liquid. However, each pipet is industrially produced to hold a specific amount of volume (Ex: a 25 mL volumetric pipet is the best tool to measure ONLY 25 mL of liquid). This feature makes volumetric pipets ineffective at reading varying volumes or volumes including very specific decimals.

    Buret

    A buret is used for the transfer of very precise amounts of liquid. They are primarily used in titrations to deliver specific, precise amounts of the titrant. A buret contains a stopcock along its side that allows one to deliver the solution gradually ensuring accuracy. The scale of burets is generally divided into 0.1 mL increments. Therefore, liquid volume measurements are recorded to the nearest 0.01 mL allowing burets to be very versatile at reading volumes that include decimals.

    Bunsen burner

    A Bunsen burner produces a gas flame used for heating in the laboratory. Caution should always be taken when using an open flame.  

    Calorimeter

    A calorimeter is used to measure the change in heat from a reaction while minimizing the transfer of heat to the outside environment. In general chemistry labs, a simple setup of two stacked Styrofoam cups, a lid with a hole, and a thermometer are used.

    Balance (digital)

    A digital balance is used to measure mass with a high degree of precision. A digital balance should be swept clean, then turned on and set to zero. Then, a creased piece of weighing paper should be placed on the balance and it should once again be set to zero (to exclude the weight of the weighing paper from the mass being measured). Finally, the mass being measured should carefully be transferred to weighing paper (gradually if necessary) and the measurement should be recorded.  

    pH meter

    A pH meter is used to measure the pH of a solution. Depending on the laboratory, this device may be analog or digital. A pH meter should be calibrated in solutions of known pH before use.

    Buchner funnel

    Used during vacuum filtration. It sits on top of the flask and holds the filter paper.

    Gravity filter funnel

    Used during gravity filtration (not vacuum filtration). Does not form the necessary seal for vacuum filtration and should not be used for this purpose.

    Separatory funnel

    Used to separate immiscible liquids.

    Dropping funnel

    Used to add liquid reagents (one drop at a time) to a flask.

    Powder funnel

    Used for adding solid reagents to a flask.

    Laboratory Equipment Listed in Increasing Precision

    Error Analysis

    To calculate the percentage error of a determined value against an actual value, the following formula should be used:

    (Actual - Theoretical) / Theoretical ×100 = % error

    Types of error:

    Systematic errors are errors that result from flawed equipment or experimental design. They can be detected and corrected for (for example, if your scale used to measure mass was not set to zero beforehand and thus every measurement is off by +5 mg, this error can be adjusted for). Systematic errors can still be precise but will not necessarily be accurate (for more on precision and accuracy, see the Data Analysis section below). All systematic errors produced from the same source will tend to be in the same direction.

    Random errors are errors that result from human interpretation of data. For example, when determining the quantity of liquid in a graduated cylinder by reading a meniscus, you may slightly misjudge the bottom of the curve, resulting in an error of measurement. Random errors can affect both precision (e.g., you may both overestimate and underestimate some readings) and accuracy.

    Safety

    Safety in the lab is a broad topic. It is suggested that you review your lab manual from general chemistry to refresh the basics, but in general, apply common sense when answering questions about safety. The correct answer to dealing with an incident in the lab will usually be the one that effectively resolves the issue while exercising the most caution possible to minimize harm to oneself and others.

    Safety shower

    Used to wash off chemicals exposed to the skin. Clothing that has been exposed to chemical spills should also be removed while using the safety shower.

    Eyewash

    Used to rinse out eyes if exposed to chemicals. Eyelids should be held open during rinsing.

    Safety goggles

    Safety goggles should be worn at all times during lab, and not removed until leaving the lab. They protect the eyes from exposure to chemicals from splashing or explosions.

    Disposable gloves

    Should be worn to protect the hands from accidental exposure to chemicals.  

    Spill neutralizers

    Used to neutralize chemicals (particularly acids and bases) if accidentally spilled in the lab.

    Fume hood

    Remove potentially harmful vapors that can be emitted during a reaction. All work performed under a fume hood should be done so at a reasonable distance away from the front of the hood so that proper ventilation is achieved.

    Fire Safety

    If a fire breaks out in the lab, the priority is the safety of everyone involved. Do not focus on turning off instruments as this will unlikely make any difference in the growth of the fire. Focus on getting everyone out of the lab as quickly as possible to ensure the safety of all individuals.

    Data Analysis

    Significant digits

    Significant digits are used to indicate the uncertainty of a measurement. You generally do not need to worry about significant digits when performing calculations, but you may be asked specifically about them during the exam. For this reason it is helpful to review how to determine the correct number of significant digits, and how to handle calculations so that the answer contains the appropriate amount of accuracy.

    Shortcut to determine the number of significant digits present:
    1. If there are decimals anywhere in the number, count all digits starting from the first non-zero number as significant. Examples: in the number 40.02, there are 4 significant digits. In the number 00.056700, there are 5 significant digits. The underlined numbers indicate the significant digits.

    2. If there are no decimals anywhere in the number, start counting from the first non-zero number, and stop counting at the last non-zero number.  Examples: in the number 56700 there are 3 significant digits. In the number 2002 there are 4 significant digits.

    You should also know the correct number of significant digits to use in your answer when performing calculations:

    1. When multiplying or dividing numbers with differing amounts of significant digits, the answer should be limited to the lesser number of significant digits. Example: say you were asked to multiply 45.00 * 5.0 First, determine the number of significant digits: 45.00 has 4 significant digits, while 5.0 has only 2 significant digits. Therefore, the answer should be rounded to 2 significant digits. 45.00 * 5.0 is 225, but our answer should only have 2 significant digits, so we round up to 230 as the correct answer.

    2. When adding or subtracting numbers with differing amounts of significant digits, things get a bit more complicated. Here, the answer should be presented to the digit of least accuracy in the numbers being added or subtracted. Let us review two examples:

    55.8 + 42.39

    Above, the least accurate place is underlined:  it is the tenths place in 55.8. Therefore our answer should be rounded to the least accurate decimal place. 55.8 + 42.39 = 98.19, but since our answer must be rounded to the tenths place, the correct answer is 98.2. This applies to whole numbers as well, as we will see in our next example:
    9876 + 25 + 360

    Once again the least accurate place has been underlined: it is the tens place in the number 360. Therefore our answer can be no more accurate than that digit. 9876 + 25 + 360 = 10,261, but since our answer must be rounded to the tens place, the correct answer is 10,260.

    Remember that zeros after a decimal (assuming they follow a non-zero number) do count as significant. So if you were to add 2.50 + 5.6691, the least accurate place is the hundredths place on 2.50  - the underlined zero counts as a digit of accuracy, so here our normal total would be 8.1691 but our adjusted total for accuracy is 8.17 – once again our answer is presented to the least accurate digit present.

    Save 100+ hours of your life studying with Bootcamp.com

    Get everything you need in one place. Start studying today for free.

    Start Studying for Free
    Hannah Brein, DAT Bootcamp Student